How I build the show

Seattle Light Show is my hobby here in West Seattle. If I can make it myself, I do. I print the little clips that hold the lights, solder the wiring, build the frames for the screens, and put together the soundtrack.

The show by the numbers

Show wire

5,600 ft

About 9¼ Space Needles tall.

Soldering

720 joints

240 pigtails, 3 wires each. I solder and heat-shrink every joint by hand.

How I set the lights to music

I start with the music. Then I listen for the beats, bass notes, and words I want the lights to pick up. Each sound can get a different part of the display moving.

The Halloween mashup

  1. Stranger Things
  2. Seven Nation Army
  3. Ghostbusters
  4. Thriller
Put the songs together FL Studio

I use FL Studio to put together mashups and make my own cuts of songs for the show.

Audio clips from the Halloween mashup arranged in the FL Studio Playlist.
The Halloween mashup in the FL Studio Playlist.
Mark the sounds I want to use SpectraLayers Pro

Once the track is ready, I use SpectraLayers to add timing marks for the lights.

The saved mashup’s waveform and colored spectrogram alongside its vocals, drums, bass, and other layers.
The layers on the right let me listen to one part of the mix at a time.
Two blue timing lines over the isolated cymbal spectrogram. The first line sits at the start of a bright green cymbal hit.
The blue lines mark where the cymbal hits start.
Turn timing marks into lights xLights

All the props get mapped onto a 3D model of the house in xLights. That lets me see how they'll look together while I time the lights to the music. Each prop or group has a row in the Sequencer, where I add effects and line them up with the sounds I marked earlier.

For the singing props, I run the vocal track through an online tool that breaks the words into sounds and marks when each one happens. I use those marks to match the mouth shapes to the vocals, then tweak the timing by hand.

3D house layout
The house in xLights, with three arches along the front, four upright poles, and strands on the maple tree.
Sequencer Arches
The Halloween mashup in xLights. Colored timing tracks sit above rows of effects for each prop group.

I group the three arches so I can send a sweep of light across all of them.

Ask me about sequencing

Screens out front

The big P5 screen

Red, green, blue, and yellow test lines across the big LED screen on the workbench.
This test pattern tells me the panels are all connected and working properly.

The big screen is made from smaller LED panels fitted together, the same idea behind the huge screens on billboards and the sides of buildings. P5 means the LED pixels are spaced 5 millimeters apart, measured from center to center. Each repeated shape in the test pattern marks one panel. You can combine panels into different sizes and shapes, so you're not stuck with the size of a ready-made screen.

See how the screen goes together

I built the metal frame, wired the panels together, and fitted an aluminum cover over the back. I got most of the build materials at Home Depot and ordered the panels from AliExpress.

Locking clamps hold a rectangular aluminum frame on a metal workbench.
The aluminum frame taking shape on the bench.
Metal support rails laid across the circuit-board backs of the LED panels.
These rails hold the rows of panels in place.
Metal plates are fitted over a grid of P5 boards, with some boards and ribbon cables still exposed.
I fit the back plates with cutouts for the cables.
Red and black wires bundled along the exposed backs of the matrix panels.
I run power across the backs of the panels.
Two vented power supplies and their wiring sit inside an open aluminum enclosure.
The power supplies get their own box on the back of the screen.
A large aluminum cover for the back of the matrix.
The aluminum cover that goes on after the wiring is in place.

Tune-to sign

The finished tune-to sign reads 87.9 FM beside the front steps during the light show.
The finished sign showing 87.9 FM during the show.

I made the tune-to sign from an old aquarium light housing I had lying around. I sealed it up and printed brackets to hold three P5 panels inside. A Raspberry Pi 4 and a Colorlight card drive the display. I printed the bracket that holds the sign to the post, too.

See the sign on the workbench
  • Square plate with four corner holes on top of a post sleeve with a side hole.
    Tune-to Sign Post Bracket

    The flat plate goes against the sign, and the sleeve fits the post.

Three panels in a row display colored triangles beside their open enclosure on the workbench.
I use the triangles to check that all three panels are working together.
The backs of the sign panels beside an open case with circuit boards, a power supply, and wiring.
With the case open, you can see the power supply and wiring.

Inside the control boxes

Each prop needs power and a signal to tell it what to do. These are two of the control boxes out in the yard, with their controller boards, power supplies, and all the connections going out to the lights. I solder the connections, cover each joint with heat-shrink tubing, and test the wiring on the bench. It’s a lot easier to fix a bad connection while I can still reach it.

An open gray enclosure in the yard holds a Kulp controller board with rows of wired green terminals.
A controller box in the yard. Each connection goes out to part of the display.
A large power supply sits above a wired controller board inside an open outdoor enclosure.
Another box, with the power supply above the controller and cables leaving through the sides.
Networking, audio, and a closer look at the wiring
A network switch and Ethernet cables inside a gray enclosure with cable fittings along the bottom.
The show network has its own enclosure.
An audio amplifier and connected cables behind the clear cover of an outdoor box.
The audio hardware, seen through the clear cover.
A hand holds the back of a round connector above the wiring in an open enclosure.
One of the connectors I wired for an earlier build.

How the lights attach

I screw a small square base to the house. The tapered slot on the back of the holder slides over it. When I need a different holder, I can leave the base right where it is.

  • Small square mounting base for the slide-on light holders.
    Screw-on Slide Base

    One screw goes through the middle. The tapered sides guide the holder into place.

Exploded view of the actual printed holder and square mounting base. The base has a center screw hole. An arrow shows the holder sliding down over the base.
The holder slides down over the base. The inset shows where the screw goes.
  • Rear view of a straight ribbon holder showing the tapered receiving slot.
    Straight Ribbon Light Holder

    I use this channel to keep the LED ribbon in place along a straight run.

  • Open-sided ribbon holder with a raised rail inside the channel and a mounting block at the rear.
    Corner Ribbon Light Holder

    This one supports the ribbon where the run turns a corner.

  • Rear view of a corner ribbon holder with its tapered slot turned across the back.
    Alternate Corner Ribbon Light Holder

    I turned the slot the other way for corners that face a different direction.

  • The back of a long ribbon holder showing its tapered receiving slot.
    Horizontal Ribbon Light Holder

    This holder keeps the ribbon level along the house.

From the model to the house

A pale printed holder fixed to the house supports a horizontal strip of wired pixel lights.
A printed holder supporting the lights on the house.
A brown printed holder on a wooden fence supports a vertical strip of pixel lights.
The same idea on the wood fence, with room behind the light strip for its wires.

A holder for one light

I made a little cradle for a single square LED module. The tabs are for mounting screws, and the cutouts give the wires room to pass through.

  • Open cradle with curved retaining arms and a round mounting hole on each side.
    Square LED Module Holder

    The sides keep one LED module seated while the wires pass through the openings.

Square LED modules sit in dark printed cradles along the bottom of a wooden fence, joined by white wires.
The Square LED Module Holders installed along the fence.
A hand holds a square LED module seated in a translucent printed cradle with white wires on either side.
The LED fits into the cradle with room for wires on either side.

What holds the yard props up

PVC, repurposed light poles, PEX tubing, and a few parts from the printer.

The PVC spiral

Eight white PVC spokes meet at a black printed hub behind a spiral of lights on the fence.
The Eight-Pole Holder in use at the center of the spiral.

PVC spokes support the spiral, and the eight-socket hub I printed holds them together in the middle. The lights wind around that frame.

See the printed hub
  • Octagonal block with a circular pole socket on each side.
    Eight-Pole Holder

    Eight sockets hold the PVC spokes at the center of my spiral prop.

Repurposed light poles

Vertical LED ribbon strips held upright on repurposed outdoor light poles with printed brackets, beside the fence and PEX arches.
The vertical pole lights with the mounts I printed to hold the lights.

These started as poles made to go in the ground and hold up outdoor string or rope lights, like you'd use across a backyard. I reused just the poles and printed mounting brackets so they could hold the LED ribbon strips upright.

PEX arches

A white PEX tube forms a low arch in front of the brick wall and pixel fence.
One of the arches with the lights off. The LED strip is inside the tube.

The arches are PEX tubes with an LED strip run through the inside. The tube gives each arch its shape and spreads the light along the curve.

More printed parts

Fence and gutter mounts

I shape each mount around what it needs to grab, like the top of the fence or the edge of a gutter. PVC also turns up in my fence supports. The photo shows the printed clip holding the light channel against the white fence.

A white printed clip hooks over a white fence rail and holds a light channel along its front edge.
The White Fence LED Channel Holder attached to the fence.
  • U-shaped fence bracket with two short retaining hooks on one side.
    White Fence LED Channel Holder

    I shaped the hooks to fit the white fence and keep the LED channel in place.

  • Short block with tapered sides and a single countersunk hole.
    ¾-Inch Wood Fence Mount

    The hole is recessed so the screw head can sit flush in the block.

  • C-shaped ribbon clip with retaining lips and a curved gutter hook.
    Gutter LED Ribbon Holder

    One side hooks over the gutter. The other holds the ribbon.

Warlock prop mounts

I made several rings for the middle of the Warlock and brackets to hold it around the outside edge.

  • Thin hexagonal ring with a wide center opening and twelve round holes.
    Warlock Hexagonal Center Ring

    I kept this ring flat so it sits low around the center opening.

  • T-shaped bracket with a round opening in its arm and two sets of mounting holes.
    Warlock Open-Ended Perimeter Bracket

    I left an opening in the arm of this bracket for the outside edge.

  • Flat circular ring with a large center opening and four pairs of small holes.
    Warlock Rear Center Ring

    This flat ring sits behind the center of the Warlock.

  • Round base with small mounting holes and a raised cylinder with a center hole.
    Warlock Front Center Ring

    The raised rim goes around the center opening on the front.

  • Tall scalloped hub with round side openings on a circular flange.
    Warlock Raised Center Hub

    This version raises the center while keeping the mounting holes around the base.

  • Open ring with four inward-facing tabs, each with three round holes.
    Warlock Center Ring Backing

    The tabs reach inward and give me places to fasten the backing.

  • Oval plate with paired mounting holes around a short raised cylinder.
    Warlock Oval Perimeter Mount

    The oval base puts fastening holes on either side of the raised post.

  • T-shaped bracket with a rounded center arm and eight holes across its mounting plate.
    Warlock Wide Perimeter Bracket

    The wide plate gives me several spots to fasten this bracket around the edge.

Want to print one of these? Send me the part name.

Request an STL